Question 1

RIP routing has been enabled on the router.Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.3?

Accepted Answer

A)  router(config-router-rip) # network 192.168.20.0
B)  router(config-router) # network 192.168.20.0
C)  router(config) # network 192.168.20.0
D)  router(config-router) # network 192.168.20.3
E)  router(config) # network 192.168.20.3F) A) and D)
G) A) and B) B

Question 2

After issuing the proper command to configure a static route,the prompt does which of the following?

Accepted Answer

A)  Changes to router (config-static) #
B)  Changes to router(config-static) 
C)  Does not change; remains at router (config#) 
D)  Does not change; remains at router (config) #E) B) and C)
F) All of the above

Question 3

Which of the following best characterizes OSPF's Area 0?

Accepted Answer

A)  Used to hide data packets
B)  Root or the backbone for the network
C)  Inverse mask bits
D)  Route selection bitsE) B) and D)
F) A) and C) B

Question 4

Which prompt is displayed after issuing the command to enable RIP routing?

Accepted Answer

A)  router(config-router-rip) #
B)  router(config-router) 
C)  router#(config-router) 
D)  router(config-router) #
E)  router#(config-router-rip) F) C) and E)
G) None of the above

Question 5

Which of the following commands displays the router's running-configuration?

Accepted Answer

A)  router> show ip running-configuration
B)  router# show rip running-configuration
C)  router# show running-configuration
D)  router# show configurationE) A) and C)
F) All of the above

Question 6

From which prompt is the command to specify RIP routing issued?

Accepted Answer

A)  Router(config) 
B)  Router(config) >
C)  Router(config) #
D)  Router(config-router-rip) #E) B) and C)
F) A) and D)

Question 7

You want to configure OSPF on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Accepted Answer

A)  network 10.0.0.0 255.0.0.0 area 0
B)  network 10.0.0.0 0.255.255.255 area 0
C)  network 10.0.0.0 255.255.255.0 area 0
D)  network 10.0.0.0 255.255.255.255 area 0E) A) and D)
F) A) and C)

Question 8

What is the administrative distance of the RIP routing protocol?

Accepted Answer

A)  120
B)  1
C)  90
D)  110
E)  100F) B) and D)
G) C) and D)

Question 9

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Accepted Answer

A)  show protocol
B)  show ip protocol
C)  show protocol dynamic
D)  show protocol link-stateE) A) and C)
F) None of the above

Question 10

Which of the following commands can be used to display the routes configured on the router?

Accepted Answer

A)  router> show route
B)  router# show route
C)  router# show rip route
D)  router# show ip routeE) All of the above
F) A) and B)

Question 11

Which of the following is not an advantage of OSPF?

Accepted Answer

A)  It's very easy to implement.
B)  It uses VLSM.
C)  Link-state changes are immediately reported.
D)  It's not a proprietary protocol.E) A) and C)
F) A) and D)

Question 12

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.True or False?

Accepted Answer

A) True 
 B)False

Question 13

What is the administrative distance for a directly connected route in Cisco networking?

Accepted Answer

A)  1
B)  0
C)  10
D)  20E) A) and B)
F) All of the above B

Question 14

Which of the following best characterizes areas in the OSPF protocol?

Accepted Answer

A)  Not used
B)  Used to partition a large network into small networks
C)  Used to combine small networks into one large network
D)  An inefficient use of bandwidthE) B) and C)
F) B) and D)

Question 15

Advertising a network means the routing table containing the network is shared with its neighbor routers.True or False?

Accepted Answer

A) True 
 B)False

Question 16

Which of the following router commands could be used to display the routing protocol configured on the router?

Accepted Answer

A)  router>sh ip protocol detail
B)  router# sh ip protocol
C)  router# sh protocol
D)  All of these answers are correctE) All of the above
F) B) and D)

Question 17

What is the administrative distance for RIP in Cisco networking?

Accepted Answer

A)  10
B)  90
C)  110
D)  120E) A) and B)
F) A) and C)

Question 18

What command would you use to verify that the OSPF routes you expect are in the routing table?

Accepted Answer

A)  show ip route dynamic
B)  show route
C)  show ip route ospf
D)  show ip route dynamic ospfE) C) and D)
F) A) and D)

Question 19

Which of the following commands enables you to view the route codes and routes?

Accepted Answer

A)  show ip router
B)  show ip route
C)  show routes
D)  show static routesE) C) and D)
F) B) and C)

Question 20

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

Accepted Answer

A)  LSAs
B)  ARP messages
C)  Ping
D)  "Hello" packetsE) None of the above
F) All of the above

Exam 9: Routing Protocols

RIP routing has been enabled on the router.Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.3?

Correct AnswerverifiedB

After issuing the proper command to configure a static route,the prompt does which of the following?

Correct AnswerverifiedShow Answer

Which of the following best characterizes OSPF's Area 0?

Correct AnswerverifiedB

Which prompt is displayed after issuing the command to enable RIP routing?

Correct AnswerverifiedShow Answer

Which of the following commands displays the router's running-configuration?

Correct AnswerverifiedShow Answer

From which prompt is the command to specify RIP routing issued?

Correct AnswerverifiedShow Answer

You want to configure OSPF on five interfaces all in the 10.X.X.X network range using a single command.What command does this?

Correct AnswerverifiedShow Answer

What is the administrative distance of the RIP routing protocol?

Correct AnswerverifiedShow Answer

What command will provide information about the dynamic routing protocols on your Cisco router and their configurations?

Correct AnswerverifiedShow Answer

Which of the following commands can be used to display the routes configured on the router?

Correct AnswerverifiedShow Answer

Which of the following is not an advantage of OSPF?

Correct AnswerverifiedShow Answer

A computer with an IP address of 10.10.5.1 sends a data packet with a destination IP address of 10.5.10.20 using a subnet mask of 255.255.255.0.The packet stays in the LAN.True or False?

Correct AnswerverifiedShow Answer

What is the administrative distance for a directly connected route in Cisco networking?

Correct AnswerverifiedB

Which of the following best characterizes areas in the OSPF protocol?

Correct AnswerverifiedShow Answer

Advertising a network means the routing table containing the network is shared with its neighbor routers.True or False?

Correct AnswerverifiedShow Answer

Which of the following router commands could be used to display the routing protocol configured on the router?

Correct AnswerverifiedShow Answer

What is the administrative distance for RIP in Cisco networking?

Correct AnswerverifiedShow Answer

What command would you use to verify that the OSPF routes you expect are in the routing table?

Correct AnswerverifiedShow Answer

Which of the following commands enables you to view the route codes and routes?

Correct AnswerverifiedShow Answer

Which of the following does the OSPF routing protocol use to verify that a link between to routers is active and the routers are communicating?

Correct AnswerverifiedShow Answer

Correct Answer
verified
B

Correct Answer
verified

Correct Answer
verified
B

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
B

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified